The HP A is capable of making highly accurate measurements. In order to .. you should use manual range to get to the lowest range possible for the. Hp A Pdf User Manuals. View online or download Hp A User Manual. View and Download HP A user manual online. A Multimeter pdf manual download.

Author: Yorn Shakagul
Country: Canada
Language: English (Spanish)
Genre: Travel
Published (Last): 22 October 2011
Pages: 151
PDF File Size: 18.91 Mb
ePub File Size: 18.84 Mb
ISBN: 694-3-23856-435-5
Downloads: 55193
Price: Free* [*Free Regsitration Required]
Uploader: Gardami

Chapter 8 Specifications Configuring manuzl Highest Accuracy Measurements Configuring for Highest Accuracy Measurements The measurement configurations shown below assume that the multimeter is in its power-on or reset state.

To adjust the reading hold sensitivity band, use the TRIG menu. For hp3401a measurements, resolution is actually fixed at 6 digits. These are often a problem on old instruments, if contacts got contamination and unable to maintain low resistance connections.

Notice that the units are flashing on the right side of the display. Note that the crest factor errors do not apply manuwl input signals below Chapter 8 Specifications Interpreting Multimeter Specifications Transfer Accuracy Transfer accuracy refers to the error introduced by the multimeter due to noise and short-term drift.

File:HP A User – Mindworks

DC Undefined header A command was received that is not valid for this multimeter. Perform a calibration using the specified calibration value CALibration: Chapter 3 Features and Functions Hp34410a Overview Calibration To Change the Security Code To change the security code, you must first unsecure the multimeter, and then enter a new code.

Configuring For Highest Accuracy Measurements Noise Caused By Ground Loops Measurements will begin when the specified trigger conditions are satisfied after the INITiate command is received. Rs Interface Commands HP A Replaced components locations.

Page Chapter 4 Remote Interface Reference Simplified Programming Overview If you send two query commands without reading the response from the C a u t i o n first, and then attempt to read the second response, you may receive some data from the first response followed by the complete second response.

  FLUKE 8810A MANUAL PDF

File:HP 34401A User Manual.pdf

Declaration Of Conformity Chapter 2 Front-Panel Menu Operation A Manuaal Menu Tutorial Menu Example 1 The following steps show you how to turn on the menu, move up or down between levels, move across the choices on each level, and turn off the menu.

The default mode is 5 digits slow. Error Messages Errors are retrieved in first-in-first-out order. Not this time though, hp34401z problems detected with a switch, probed input 1.

HP 34401A User Manual

Output Approximately External Trigger Terminal Even if the cable has the proper connectors for your system, the internal wiring may not be correct. U ASIC resistor network measurement results.

Chapter 4 Remote Interface Reference Autozero Chapter 3 Features and Functions Measurement Configuration Autozero When autozero is enabled defaultthe multimeter internally disconnects the input signal following each measurement, and takes a zero reading. The Questionable Data Register Applies to all measurement functions, except continuity and diode tests. Refer to the cable and adapter diagrams on the following page to connect the multimeter to most computers or terminals.

The first reading displayed is the first reading that was stored FIFO. Chapter 4 Remote Interface Reference Simplified Programming Overview If you send two query commands without reading the response from the C a u t i o n first, and then attempt to read the second response, you may receive some data from the first response followed by the complete second response.

To Select The Remote Interface 2: The security code may contain up to 12 alphanumeric characters. If you like the article or have any questions, jump in comments!

Db Measurements Chapter 3 Features and Functions Math Operations dB Measurements Each dB measurement is the difference between the input signal and a stored relative value, with both values converted to dBm. The rate is set RS to baud when the multimeter is shipped from the factory.

  DESCARGAR QUIUBOLE PARA CHAVAS GRATIS PDF

Page 32 Chapter 2 Front-Panel Menu Operation A Front-Panel Menu Tutorial Menu Example 1 The following steps show you how to turn on the menu, move up or down between levels, move across the choices hp34401q each level, and turn off the menu. Loveland, Colorado U.

In this mode, the multimeter can output readings directly to a printer without being addressed by a bus controller over either HP-IB RS For proper operation, make sure your printer is configured in the listen always mode. Measurements Below Full Scale Temperature Coefficient and Overload Errors The HP A uses an ac measurement technique that measures and removes internal offset voltages when you select a different function or range. Check to see if you have enclosed the character string in single or double quotes and that the string contains valid characters.

Power-line Voltage Setting See the next page if you need to replace the power-line fuse.

| HP A repair and calibration worklog

Trigger Delay Chapter 3 Features and Functions Triggering Trigger Delay You can insert a delay between the trigger signal and each sample that follows. Because of the capacitance between the input LO terminal and earth approximately pF for the HP Athe source will experience different loading depending on how the input is applied.

In This Book Dc Current Measurement Errors To rack mount two instruments side-by-side, order lock-link hp34410a and flange kit All multimeters exhibit measurement errors mamual are crest factor dependent.

Baud Rate Selection rs Page 97 Chapter 3 Features and Functions Calibration Overview Calibration To Unsecure for Calibration You can unsecure the multimeter for calibration either from the front panel or remote interface.