Title, Curso de vapor Spirax Sarco. Contributor, Spirax Sarco (Firma). Publisher, Spirax Sarco, Length, 84 pages. Export Citation, BiBTeX EndNote. Curso de Vapor por Spirax Sarco, Tuvanosa, Calzada Aeropuerto # Pte Col. Nuevo Bachigualato, Culiacán, Mexico. Mon Oct 17 at. Curso de gestión impartido en Queretaro, gracias por confiar en Spirax Sarco. Expertos en soluciones de energía térmica y vapor. #atodovapor #spiraxsarco.

Author: Balkree Kagajinn
Country: Angola
Language: English (Spanish)
Genre: Literature
Published (Last): 14 July 2018
Pages: 113
PDF File Size: 6.96 Mb
ePub File Size: 17.95 Mb
ISBN: 915-8-59998-363-1
Downloads: 63023
Price: Free* [*Free Regsitration Required]
Uploader: Yozshur

¡La trampa de vapor más sustentable y de más rápida instalación!

Enviado por Luiz Felipe flag Denunciar. It must supply good quality steam at the required rate and at the right pressure. It must do this with the minimum of heat loss, and be economical in capital cost. We already know that dry saturated steam not superheated is to be used for process and heating applications and it is that with which we shall concern ourselves.

Spirax Sarco Chile | First for Steam Solutions

The pressure at which the steam is to be distributed is determined by the point of usage on the plant needing the highest pressure. We must remember however that as the steam passes through the distribution pipework, it will lose some of its pressure due to resistance to flow, and the fact that some of it will condense due to loss of heat from the pipes.

  IZBAN SEFER SAATLERI PDF

Therefore allowance should be made for this pressure loss when deciding upon the initial distribution pressure.

Summarising, we need to consider when selecting our working pressure: Pressure required at point of use Pressure drop along pipe due to resistance of flow spiarx Pipe heat losses We also know that sarrco at a higher pressure occupies less volume per kg.

It therefore follows that if we generate steam in the boiler at a much higher pressure than that needed by its application, and we distribute it at this higher pressure the bore of the distribution mains will be smaller for any given mass flow rate.

This causes considerable damage to the pipework and ancillaries. If taken from the side, or even worse from the bottom, they can carry the condensate from the main and in effect become a drain pocket. The result is very wet steam reaching the equipment.

Steam lines are no exception. Steam leaving a boiler, or other sources, is often much wetter than is appreciated and if this water is not removed, sarcoo will be poor heat transfer at the point of use this is why the steam needs to d dry. The use of a separator to remove this moisture is shown in the slide.

Sizing one is not difficult as they are always sized to match the steam line line size. This is one location where a correctly sized mechanical drain trap, such as a float trap, can be beneficial.

  DSC MAXSYS PC4020 V3.0 INSTRUCTION MANUAL PDF

As soon as steam has left the boiler, some of it must condense, to replace the heat being lost through the pipe wall. Insulation will naturally reduce the heat loss, but the heat flow and xpirax condensation rate remain as small but finite amounts and if appropriate action is not taken these amounts will accumulate.

Catálogo general de productos: Línea Spirax Sarco.

The condensate will form droplets on the inside of the pipe wall, and dd can merge into a film as they are swept along by the steam flow. The film will also gravitate towards the bottom of the pipe, and so the thickness of the water film will be greatest there.

Steam flowing over this film can raise ripples which can build up into waves. If this build up continues, the tips of the waves spigax break off, throwing droplets of condensate into the steam flow. The result is that the heat exchange equipment receives very wet steam.

If this build up continues, the tips of the waves.