View and Download Bosch DB operation and installation manual online. DB Network Card pdf manual download. Bosch DB Pdf User Manuals. View online or download Bosch DB Operation And Installation Manual. Office Manuals and free pdf instructions. Find the office and computer equipment manual you need at ManualsOnline.
|Published (Last):||2 August 2016|
|PDF File Size:||11.47 Mb|
|ePub File Size:||13.40 Mb|
|Price:||Free* [*Free Regsitration Required]|
Check the faceplate for the model number and the handler title. Reports Missing Trouble Event. Perimeter Armed Relay was added to firmware versions 6.
Yes or No If the last digit of the passcode is 8, a duress alarm is generated when the user enters boech as the last digit of the passcode.
For boscb, if User Group 1 has a window running from 8: This relay provides a steady output until all Fire points in the system are returned to normal. They report also when a Diagnostic Report is initiated from a command center or by a Sked. D Installation Instructions 9. Fail to Close Report is not sent for this area.
Bosch Appliances D9210B Network Card User Manual
Programming Four Digit Account Numbers The conversions are shown in Table 6 and Table 7. User Interface Define which functions can be used by each of the fourteen user authority levels. This d921b determines if a passcode is required when d910b to access a Custom Function from the menu list. Sub-users cannot use the passcode. The route represents the group you wish to send a group of reports.
Long or Short Long Standard duration of ground. Phone Supv Time must be programmed to use this feature.
Use this function to view all of the main events Door Cycle boscch the main event modifiers By User in the event log memory. Use separate area alarm-verification relays. It shuts off the bell when the programmed number of minutes expires. No No events in this group print at this printer. Beginning in Firmware version 6. Fire points restart bell time with each new alarm. It is only when the user attempts to Bypass Arm an area or areas that this restriction is enforced.
Perimeter points can be programmed to initiate entry delay time. Reports point forced armed. Program a 1 for Primary Destination c. Although d9210h handlers shown in Table 4 can be used to program any of the new control panels, not all of the x9210b operate.
Setting the Dipswitch and Taggi The function can be executed without entering a passcode.
When programming this type of protection, consider also using the Buzz on Fault and Local While Disarmed options. Yes or No Yes Panel-wide trouble tones sound and visual displays show at this command center. Command numbers are shown in the column labeled Command. Blank, E, or P P Passcode: 9d210b the following test to confirm you can convert properly: P Silent Bell must be No for the bell to ring upon alarm. These special point types do not respond the same way to the point response entry as Point Types 1, 2, and 3.
Perimeter points are armed with all Arming functions. Page 16 – Step 3: Visual displays still show.
Bosch D9210b Series Access Control Interface Module
Figure 3 shows all the users for User Group as they would appear. See the Enhanced Command Center prompt in Section 2.
Blank, E, or P This function deletes the passcode, master user, and all sub-users associated with the user number. Blank or E 1 Disarm Use the disarming function to disarm areas that are master armed or perimeter armed. This item determines if this area can restrict Opening and Closing Report activity.
Reports failure of AC power to control panel. Use this relay as an option to create audible annunciation using the command centers for all applications excluding commercial fire systems. Command Center Programming Choices Users can bypass more points than the number entered here during the disarmed state.
A sked cannot activate this state.
Bosch DB Access Control Interface Module Fire Alarm | eBay
Up to 32 functions M Function s can be programmed. After one alarm, alarms on any Nonfire points in the same area cannot restart the bell until the armed state changes. This number is D92110b 2, referred to in the prompts in Section 2. Reports Fire Walk End Event.