A datasheet, A pdf, A data sheet, datasheet, data sheet, pdf, Intel, PROGRAMMABLE PERIPHERAL INTERFACE. INTEL (Programmable Peripheral Interface). In previous lectures we have discussed how to interface I/O devices with the system bys. If an input device. The Intel (or i) programmable peripheral interface (PPI) chip was developed and manufactured The i was also used with the Intel and Intel and their descendants and found .. “Intel 82c55 PPI Datasheet” (PDF ).

Author: Fauzragore Tygoshakar
Country: Cyprus
Language: English (Spanish)
Genre: Life
Published (Last): 19 July 2008
Pages: 114
PDF File Size: 11.87 Mb
ePub File Size: 6.26 Mb
ISBN: 836-3-87362-887-6
Downloads: 23655
Price: Free* [*Free Regsitration Required]
Uploader: Shakora

In this mode, the may be used to extend the system datasheey to a slave microprocessor or to transfer data bytes to and from a floppy disk controller. Retrieved 3 June If from the previous operation, port A is initialized as an output port and if is not reset before using the current configuration, then there is a possibility of damage of either the input device connected or or both, since both and the device connected will be sending out data.

Address lines A 1 and A 0 allow to access a data register for each port or a control register, as listed below:. All of these chips were originally available in a pin DIL package. Some of the pins of port C function as handshake lines.

Intel 8255

For example, if port B and upper port C have to be initialized as input ports and lower port C and port A as output ports all in mode It is an active-low signal, i. Interrupt logic is supported. This means that data can be input or output on the same eight lines PA0 – PA7. For example, if port B and upper port C have to be initialized as input ports and datashset port C and port A as output ports all in mode Each line of port C PC 7 – PC 0 can be datasheey or reset by writing a suitable value to the control word register.

  ANALISIS FRAMING ERIYANTO PDF

The is a member of the MCS Family of chips, designed by Intel for use with their and microprocessors and their descendants [1]. When we wish to use port A or port B for handshake strobed input or output operation, we initialise that port in mode 1 port Vatasheet and port B can be initilalised to operate in different modes, i. Microprocessor And Its Applications. Some of the pins of datasheett C function as handshake lines. Retrieved from ” https: As an example, if it is needed that PC 5 be set, then in the control word.

For port B in this mode irrespective of whether is acting as an input datashfet or output portPC0, PC1 and PC2 pins function as handshake lines.

It was later cloned by other manufacturers.

Peripheral Parallel Interface for Parallel Port

Input and Output data are latched. When we wish to use port A or port B for handshake strobed input or output operation, we initialise that port in mode 1 port A and port B can be initilalised to operate in different modes, i. So, without latching, the outputs would become invalid as soon as the write cycle finishes.

Since the two halves of port C are independent, they may be dataasheet such that one-half is initialized as an input port while the other half is initialized as an output port. In this mode, the may be used to extend the system bus to a slave microprocessor or to transfer data bytes to and from a floppy disk controller.

This is required because the data only stays on the bus for one cycle.

The is also directly compatible with the Zas well as many Intel processors. The two modes are selected on the basis of the value present at the D 7 bit of the control word register. The two halves of port C can be either used together as an additional 8-bit port, or they can be used as individual 4-bit ports.

  LE RAPPRESENTAZIONI SOCIALI MOSCOVICI PDF

Port A can be used for bidirectional handshake data transfer. This means that data can be input or output on the same eight lines PA0 – PA7.

Programmable Peripheral Interface – Intel Chipset Datasheet

The Intel or i programmable peripheral interface PPI chip was developed and manufactured by Intel in the first half of the s for the Intel microprocessor and is a member of the MCS Family of chips.

Input and Output data are latched. Since the two halves of port C are independent, they may be used such that one-half is initialized as an input port while the other half is initialized as an output port.

It is an active-low signal, i.

From Wikipedia, the free encyclopedia. Only port A can be initialized in this mode.

Acknowledgement and handshaking signals are provided to maintain proper data flow 2855 synchronisation between the data transmitter and receiver. Only port A can be initialized in this mode. The control signal chip select CS pin 6 is used to enable the ;pi. The inputs are not latched because the CPU only has to read their current values, then store the data in a CPU register or memory if it needs to be referenced at a later time.

Views Read Edit View history. As an example, consider an input device connected to at port A.